Water on the Roof
This Medium Pipe Chase Housing in the photo below solved a unique problem. How do you get a water line to the roof without x-raying the concrete and coring? This is a post tension roof with conduits in the concrete. The small pipe coming off this Pipe Chase Housing once penetrated to roof on its own. We found this pipe from below and discovered there was enough room to go beside it. So we used the Pipe Chase Housing to eliminate the x-ray and core. The savings paid for the Pipe Chase Housing and we have a successful and great looking job.
Medium Pipe Chase Housing
Model AL 1001
Dimensions for AL1001.
Housing Length 20 1/2 inches
Housing Width 14 1/2 inches
Housing Height (without Curb) 13 1/2 inches
There are three parts to the Height. The lid is 2 inches. The center 8 1/2 inches and the skirt at 3 inches.
Medium Curb AL 1012 Dimensions
Curb Length 19 1/4
Curb Width 13 1/4
Curb Height (without Housing) 11 1/2
The Curb has a two inch flange out to screw to the roof deck. Screw holes are on 2 inch centers.
Standard Models Avalable.
AL 1001 Aluminum Housing and Curb. Stock item.
SS 1001 Stainless Housing and Curb. Non stock item.
Housing Length 20 1/2 inches
Housing Width 14 1/2 inches
Housing Height (without Curb) 13 1/2 inches
There are three parts to the Height. The lid is 2 inches. The center 8 1/2 inches and the skirt at 3 inches.
Medium Curb AL 1012 Dimensions
Curb Length 19 1/4
Curb Width 13 1/4
Curb Height (without Housing) 11 1/2
The Curb has a two inch flange out to screw to the roof deck. Screw holes are on 2 inch centers.
Standard Models Avalable.
AL 1001 Aluminum Housing and Curb. Stock item.
SS 1001 Stainless Housing and Curb. Non stock item.
This is a before photo of a re-roofing project. The black pipes are chilled water lines from a small chiller on the roof. Notice the chilled water line going down between the supply and return air duct work. There is no way anyone could have gotten in there to seal that penetration. From inside we could see daylight up through the hole. This is an upsidedown roof. over the years all the cracks filled in with bird futilizer and the weeds started to grow. It was an old roof and ready to be replaced.
This is the after photo. The Contractor wanted us to clean it all up. So we used the Medium Pipe Chase Housing to consolidate the piping and organize it. What you can’t see is the rearranging of the piping inside to housing. This was done to eliminate pipes crossing over pipes on the roof. We also hooked up the water so they could clean the cottonwood out of the equipment coils on the roof. The Electrician surprised me by running liquid tight from the roof down to a junction box in the ceiling. That was a very fast and easy way to do it.
Features:
1. Up to 18 pipes to the roof in one AL 1001 Pipe Chase Housing.
2. Designed for 4 condensing units. Two on each side.
3. Water Bib. Bibs must be on a BFP and winter draindown.
4. Welded Aluminum construction with all stainless hardware.
5. Powder Coated.
6. Housings and Curbs are available in Stainless Steel. Non stock.
7. We can build to your wind load requirements. Non stock.
8. We provide a hole for the Electrician to mount a GFCI.
9. Lid gasket is protected from the elements.
10. Built in skirt to protect the leading edge of the roof.
11. All mounting and lid hardware is designed so it dose not penetrate the Housing for additional protection.
12. Compress the leading edge of the roof between the housing and the top of the curb with a gasketed bolted connection.
1. Up to 18 pipes to the roof in one AL 1001 Pipe Chase Housing.
2. Designed for 4 condensing units. Two on each side.
3. Water Bib. Bibs must be on a BFP and winter draindown.
4. Welded Aluminum construction with all stainless hardware.
5. Powder Coated.
6. Housings and Curbs are available in Stainless Steel. Non stock.
7. We can build to your wind load requirements. Non stock.
8. We provide a hole for the Electrician to mount a GFCI.
9. Lid gasket is protected from the elements.
10. Built in skirt to protect the leading edge of the roof.
11. All mounting and lid hardware is designed so it dose not penetrate the Housing for additional protection.
12. Compress the leading edge of the roof between the housing and the top of the curb with a gasketed bolted connection.
Medium Curb AL 1012 Dimensions
Curb Length 19 1/4
Curb Width 13 1/4
Curb Height (without Housing) 11 1/2
The Curb has a two inch flange out to screw to the roof deck. Screw holes are on 2 inch centers.
Curb Length 19 1/4
Curb Width 13 1/4
Curb Height (without Housing) 11 1/2
The Curb has a two inch flange out to screw to the roof deck. Screw holes are on 2 inch centers.
